pardus ve skystar?

Konu: pardus ve skystar?

pardus 2007 de skystar 2 de ses gelmiyor neyapabilirim

Konu: pardus ve skystar?

arkdaşlar şifreli kanallar olmadan yabancı uydular pek işe yaramıyor? plugin dosyası yüklenmiyor mu ? başka programlarda mı yok Linux dağıtımları için ? PErformans Pardusta çok iyi ama... EKlentiler olmadan da...

Konu: pardus ve skystar?

pardus 1.0 kurulu sistemde ss2 (2.6c)den sinyal alamıyorum..lnb ayarlarınıda yaptım fakat kanal arama yaptığımda tık yok..biri bunu daha detaylı anlatabilirmi acaba...

Konu: pardus ve skystar?


arkadaşım....
hotbird'de ben şöyle yaptım....
1- windows xp ye kurulu program dvb yi açtım...
2- kanalları açtım...
3- bir kanalın üstüne sağ tıklayıp, kanal özelliklerini buldum...
4- buradaki pid, sid v.s değerlerini (o kanalın) notpad'e kaydettim....
sen kağıt kalemlede not alabilirsin... çünkü
5- ben de hem xp, hem pardus kurulu....aynı makinada...
6- bu notepadi pardusta açtım..masaüstünde...
7- pardusta kanal ararken bu sid, pid değerlerini sadece bir kanal için girersen.... o servis sağlayıcının mesela tps.... bütün kanallarını açar...
(görüntü ve ses değerleri bölümü ...kaffein programında bu değerler girilecek )
mesela sadece tps den action (macera) kanalının değerlerini gir....
ondan sonra tüm absat açılsın...
------------------------------------------------------
daha sonraki taramalarda artık hepsini tarar...
türksatta da, diğer uydularda da aynı yöntemi uygula...
ama bulduğun kanalları kaydet.... bir kereliğine...
--------------------------------------------------------
pardus ta hazır kanal dosyası da vardır belki.... linux forumlara bak...
ayrıca şifreli kanalları açmak için progr dvb benzeri vdr diye bir program olduğunu yukarıda bir arkadaş (sanırım teachers )yazmış....
ben daha kurmaya(vdr) fırsat bulamadım....
sadece şifresizleri hotbird ve astra seyrediyorum şimdilik...

kolay gelsin....

not: bende PaRdUs 2007 kurulu ve tüm ayarları otomatik..... sadece lnb, diseq tanıt kafi....
zaten progr dvb kuran bunu haydi haydi yapar....
-------------------------------------------------------------------------------------

10-01-2007, 23:20 #11teachers71

Konu: pardus ve skystar?
şifreli kanallar için vdr diye bir tv programı varmış..henüz kurmadım..ama progdvb ye çok benzediğini söylüyorlar....plugin destekli imiş..detaylı bilgi için www.pardus-linux.org taki forum sayfalarına yada www.pardus.org.tr ye bakılabilir..
selamlar...

Konu: pardus ve skystar?

transponderlar hakkında...
forumda bir arkadaştan alıntı... bu topice getirdim ki derli toplu olsun....

Mesajı Gönderen Kullanıcı msahin48
Skaystar Usb si olupta windows ta çalıştıramayan varsa pardus ta çok güzel çalışıyor.Bir yıldır kullanmadığım yani 6 ay uğraşıpta düzenli çalıştıramayıpta 6aydır rafa kaldırdığım usb skystarı pardus ta taktım,kaffeine diye programı var çalıştırdım,tarattım ve seyrediyorum.Ne kilitlenme,ne donma,bekleme!Sen neymişsin be Pardus!
Paylaşmak istedim.

Linux'ta güncel transponder'lar için:

http://joshyfun.peque.org/transponders/kaffeine.html

Konu: pardus ve skystar?





Yukarıdaki linkten indirdiğiniz dosyayı /home/kullanıcı klasörü/.kde/share/apps/kaffeine/dvb-s klasörüne yapıştırınız.Kaffeine den taratırsanız yeni kanallar eklenmiş olur.Yukarıdaki kullanıcı klasörü Pardus'u yüklerken verdiğiniz kullanıcı adınızdır.Ayrıca kde klasörünün önündeki noktaya dikkat!

Konu: pardus ve skystar?

[quote=msahin48;818612]Yukarıdaki linkten indirdiğiniz dosyayı /home/kullanıcı klasörü/.kde/share/apps/kaffeine/dvb-s klasörüne yapıştırınız.Kaffeine den taratırsanız yeni kanallar eklenmiş olur.Yukarıdaki kullanıcı klasörü Pardus'u yüklerken verdiğiniz kullanıcı adınızdır.Ayrıca kde klasörünün önündeki noktaya dikkat!


?????? nedir bu nokta? bir püf noktası?
selamlar...
sağolasın....
vdr yi indiren ya da deneyen var mı?

Konu: pardus ve skystar?

Nokta ile başlayan klasörler gizli klasörler olduğu için normalde görünmezler.Menü çubuğunda,görünüm menüsünde "gizli dosyaları göster" demedikten sonra ya da klasörün yolunu el ile adres çubuğuna yazmadıktan sonra görünmez.
vdr'yi indirdim ama kuramadım,hata veriyor.Başarırsam burdan haber veririm.

Konu: pardus ve skystar?


o.k üstadım...sağolasın... vdr yi normal dosya güncellemeden indirmedin herhalde....

selamlar....

Konu: pardus ve skystar?

evet ben birşeyler buldum.... öncelikle niye ingilizce demeyin....
çünkü....pardus 2007 ve çok yeni....
bu bir....
****************************
Re: [Linux-donanim] 8 Mayıs 2006 Pzt 21:30:57 EEST

1- Sitesinde desteklemedigi yaziyorsa belki yapacak bir sey yoktur
gercekten. Google denediniz mi? Sizin durumunuzda olup bir seyler
basarmislar vardir belki. Fikrim yok.
2- Bu e-postaya cevap verme sebebim bu. Sky Star 2 tv kartinizin uydu
dvb oldugunu varsayiyorum. Kurmaktan kastiniz karti kullanan bir program
edinmekse vdr isimli programi deneyin. Uzaktan kumanda destegi dahil her
tur "janjan" mevcut, ekraniniz yeterince buyukse time-shift gibi
ozellikleri sebebiyle klasik uydu alicilarina tercih edeceginiz bir
program. Evdeki ana sunucumun ag isleri disindaki fonksiyonu televizyon
gorevi gormek oldu son zamanlarda (Bir de izleme firsatim olsaydi)
*************************************

bu ikiiii......
yani bu notu yazan Türk arkadaş (metin Türkçe) işi tümüyle çözmüş....
....ancak sanırım başka versiyon bir linux (pardus harici) kullanıyor...
26 nolu mesajımı okuyanlar nedenini anlayacak....

alttaki üççççççç.....
*******************************************


Linux VDR Guide (linux vdr klavuzu)

Content:
1. General information to DVB
2. Preparing the system
3. Installing VDR
4. Installing the Remote Control
5. Video Output Methods
6. Creating a Channel List
7. Starting VDR
8. Troubleshooting
----------------------------
1. General information to DVB
What is DVB?
DVB stands for Digital Video Broadcasting. DVB describes methods to transfer digital data of TV, radio, interactive services like MHP, EPG and teletext. Through data compression with MPEG-2, or H.264 for HDTV, it's possible to transfer several channels on the same frequency. The more data compression, the more channels can be transferred, but you pay it with quality loss.
DVB can be transferred in several ways. The trailing letter identifies the method of transfer, e.g. DVB-T for terrestrial transmission. There are several more types:

• DVB-S for transmission over satellites
• DVB-C for transmission over cable
• DVB-H for transmission to mobile devices (terrestrial)
• DVB-IPI for transmission over IP based networks, e.g. internet
• DVB-RC(S/C/T) return channel for the transmission of data services, e.g. broadband internet

Types and requirement of DVB cards
Besides the different methods available to receive a DVB stream, the cards are classified by their type of produced output. There are cards with a decoder implemented which offer direct access to the stream by the device /dev/video. These cards are full featured cards. Other cards have no own decoder implemented and require a software decoder on the computer and are budget cards. This implies higher system requirements. Your computer's CPU should run at at least 600 MHz, and have at least 256MB of RAM. This list is useful for identifying your card.
2. Preparing the system
Configuring the kernel
First, we must ensure that your kernel supports DVB and your DVB device. Since kernel version 2.6 the necessary drivers are included. Check your kernel configuration and make sure the following options are selected as a static driver or as modules.
*****************************
Code Listing 2.1: Required kernel options
Input Device Support --->* Event InterfaceDevice Drivers --->Multimedia Devices --->Digital Video Broadcasting Devices ---> [*] DVB For Linux * DVB Core Support M [Your driver]Additionally we have to select the proper driver for your hardware. To find out the right module for your card, we mark every driver as module. If you have a PCI card, install pciutils if you haven't already. If you want built-in drivers or you don't own a PCI card, skip this step and continue with Checking the kernel output.
Code Listing 2.2: Installing pciutils
# emerge pciutils
After booting the new kernel, we run pcimodules to list the required modules.
Code Listing 2.3: Listing the required modules
# pcimodulesohci-hcdehci-hcdsis900snd-emu10k1b2c2-flexcop-pcinvidianvidiafb
In this case we have to load the module b2c2-flexcop-pci. We add the name to /etc/modules.autoload.d/kernel-2.6.
Code Listing 2.4: Adding the module name
# echo b2c2-flexcop-pci >> /etc/modules.autoload.d/kernel-2.6
Checking the kernel output
It's recommended to mark every driver as module, so that you can add the required module dynamically, especially if you don't know the module name. If you already know the module name, select the driver as a built-in driver. Compile the kernel, install the modules and boot it. You can check if your kernel has successfully detected your card by using dmesg.
Code Listing 2.5: Checking kernel output
# dmesg | grep DVB
(If you own a TerraTec Cinergy T2, your output might look like this
DVB: registering new adaptor (TerraTec/qanu USB2.0 Highspeed DVB-T Receiver).
input: TerraTec/qanu USB2.0 Highspeed DVB-T Receiver remote control as /class/input/input23. Installing VDR
To install VDR, we just emerge it.
Code Listing 3.1: Installing VDR
# emerge vdrNow continue with Installing the Remote Control.
4. Installing the Remote Control
There are at least two ways to control VDR via an infrared remote control. If your TV card has an onboard IR receiver you can use vdr-remote. Otherwise, you most likely need to use LIRC.
Installing vdr-remote
We first install the plugin via emerge:
Code Listing 4.1: Installing vdr-remote
# emerge vdr-remote# emerge --config vdr-remoteWhen using the remote plugin for the IR port on your DVB card everything should be fine with the default config. It automatically uses the input device which has "dvb" in its name. For more advanced uses take a look at /etc/conf.d/vdr.remote.
Now, continue with Video Output Methods.
Alternative: installing LIRC
If your card can be remotely controlled (but you cannot or do not want to use vdr-remote), you may wish to configure LIRC. LIRC interprets the pressed keys and returns a name for each one. A program that supports LIRC waits for key events and runs the action configured in the config file, mostly stored in the config directory of the executing program (e.g. mplayer loads the file ~/.mplayer/lircrc). Before we install LIRC, you have to add lirc to your USE flags and add an additional entry to /etc/make.conf: LIRC_DEVICES. Use this list to find the proper arguments for the option.
Code Listing 4.2: Installing LIRC
# nano -w /etc/make.conf(Replace "devinput" with the proper driver)LIRC_DEVICES="devinput"USE="lirc"# emerge lircAt first we have to define each key code with a name. Most supported remote controls are configured already, take a look at the remote list. Download the required file and save it as /etc/lircd.conf. Now we have to find out where to access your remote control. Run the following command to get a list of the current input devices (make sure your device is running).
Code Listing 4.3: List of current input devices
# cat /proc/bus/input/devicesI: Bus=0000 Vendor=0000 Product=0000 Version=0000N: Name="TerraTec/qanu USB2.0 Highspeed DVB-T Receiver remote control"P: Phys=usb-0000:00:1d.7-1/input0S: Sysfs=/class/input/input2H: Handlers=kbd event1B: EV=100003B: KEY=108fc210 2043 0 0 0 0 8000 2080 1 9e1680 0 0 ffcIn this case we have the Terratec Cinergy T2 device plugged in, so we can access the device over /dev/input/event1. Replace event1 with the matching device in your output.
lircd needs to know the device to use. Add the following line to /etc/conf.d/lirc.conf. Remember to replace devinput with the name of your driver and event1 with the actual device.
Code Listing 4.4: Adding options to lircd
LIRCD_OPTS="-H devinput -d /dev/input/event1"It's time to start lircd:
Code Listing 4.5: Starting lircd
# /etc/init.d/lircd startNow it should be possible to watch lircd capturing and decoding key presses. Just run the command irw. Stop it by pressing Ctrl+C when you have enough.
Code Listing 4.6: Testing LIRC
# irw0000000000001aa2 00 Exit Technisat_TTS35AI.conf0000000000001a8d 00 Mute Technisat_TTS35AI.conf0000000000000a97 00 OK Technisat_TTS35AI.conf0000000000000a97 01 OK Technisat_TTS35AI.conf0000000000000a92 00 Menu Technisat_TTS35AI.conf****, add it to the default runlevel so that it starts automatically at boot.
Code Listing 4.7: Adding lircd to the default runlevel
# rc-update add lircd defaultTo be able to use your remote control, you must enable LIRC support in VDR. Add the following line to /etc/conf.d/vdr:
Code Listing 4.8: Enabling support for LIRC
# nano -w /etc/conf.d/vdrIR_CTRL="lirc"5. Video Output Methods
You now need to decide on one (and only one!) of the following video output devices which show the picture and the overlayed On Screen Display (OSD).
Hardware decoding: full-featured DVB cards
Users of these expensive cards need not install anything else, so you may continue with configuring your channel list.
Hardware decoding: DXR3/Hollywood+ cards
To use a DXR3 card for VDR output we need the vdr-dxr3 plugin.
Code Listing 5.1: Installing the plugin
# emerge vdr-dxr3# echo em8300 >> /etc/modules.autoload.d/kernel-2.6The em8300 module need some configuration that depends on the exact revision of that card.
Continue with configuring your channel list.
Hardware decoding: PVR350 cards
As PVR350 cards have an onboard MPEG-Decoder chip we want to make use of that. We need to install the vdr-pvr350 plugin. If ivtv-driver is not yet installed emerge will automatically install it for you. To have the ivtv module loaded at boot we add it to /etc/modules.autoload.d/kernel-2.6:
Code Listing 5.2: Installing PVR350-Plugin
# emerge vdr-pvr350# echo ivtv >> /etc/modules.autoload.d/kernel-2.6Continue with configuring your channel list.
Software decoding: vdr-softdevice
To install it, we have to emerge vdr-softdevice. Don't forget to enable the plugin.
Code Listing 5.3: Installing the softdevice plugin
# emerge vdr-softdevice# emerge --config vdr-softdeviceTo select the proper video and audio output, edit /etc/conf.d/vdr.softdevice.
For now, we will only describe the shm ("shared memory") method. This is already enabled in the installed config file (Setting SOFTDEVICE_VIDEO_OUT). Later you need to start ShmClient to get a window showing the picture.
Note: If you do not want to think about a separate keyboard layout for controlling VDR with softdevice/shm there is a remote configuration file available at Matthias Schwarzott's devspace. You will need to copy it to /etc/vdr/remote.conf and run chown vdr:vdr on the file to get it working.
Continue with configuring your channel list.
Software decoding: vdr-xineliboutput
Some people prefer to use vdr-xineliboutput, because it can also work remotely. We'll now teach you how to configure vdr-xineliboutput on your host and client. First, the host setup:
Code Listing 5.4: Installing vdr-xineliboutput
# emerge vdr-xineliboutput# emerge --config vdr-xineliboutputAdding command line options at this point is crucial for xineliboutput to work. For more options, see vdr --help.
Code Listing 5.5: Adding command line options to /etc/conf.d/vdr.xineliboutput
_EXTRAOPTS="--local=none --remote=37890"The **** step is to edit /etc/vdr/svdrphosts.conf. This file describes a number of host addresses that are allowed to connect to the SVDRP port of the video disk recorder running on the host system.
Code Listing 5.6: Editing /etc/vdr/svdrphosts.conf
(The proper syntax is: IP-Address[/Netmask])127.0.0.1 (always accept localhost)192.168.1.0/24 (any host on the local net)#204.152.189.113 (a specific host)#0.0.0.0/0 (any host on any net - USE THIS WITH CARE!)If you only want to use vdr-xineliboutput to view the picture on the same computer as the one running VDR you can continue with configuring your channel list.
Otherwise, you now simply emerge media-plugins/vdr-xineliboutput on your client:
Code Listing 5.7: Client setup
# emerge vdr-xineliboutputLater (after having started VDR) you will use the command vdr-sxfe xvdr://hostname to connect to VDR and view its picture and OSD.
Continue with configuring your channel list.
Note: There is also a plugin which just simulates the existance of a real output device (vdr-dummydevice) for some fancy uses like record-only servers, but that is more advanced than a normal VDR setup.
6. Creating a Channel List
To make VDR really useful you need to create an appropriate channel list. There is more than one way to get a working list of channels (besides downloading one). The channel list installed by default is for DVB-S reception on Astra on 19.2°E.
Using dvbscan from linuxtv-dvb-apps
Code Listing 6.1: Installing linuxtv-dvb-apps
# emerge linuxtv-dvb-appsFind the correct frequency list for your region and type of reception. These files are stored under /usr/share/dvb/scan. For reception with DVB-T in Germany, Region Nuernberg you need to use /usr/share/dvb/scan/dvb-t/de-Nuernberg.
Code Listing 6.2: Scanning with dvbscan
$ dvbscan -o vdr /usr/share/dvb/scan/dvb-t/de-Nuernberg > /etc/vdr/channels.confUsing vdr-reelchannelscan
First, delete the contents of the existing channel list.
Code Listing 6.3: Cleaning old channel-list
# rm /etc/vdr/channels.conf
Code Listing 6.4: Installing and activating vdr-reelchannelscan
# emerge vdr-reelchannelscan# emerge --config vdr-reelchannelscanChannels for systems using vdr-analogtv
You'll probably want to configure your channels at this point. The VDR project provides you with some examples which can be found at /usr/share/doc/vdr-analogtv-$version/examples/, as long as you've installed >=media-plugins/vdr-analogtv-1.0.00-r1.
7. Starting VDR
After having all basic software parts ready on the system you need to configure VDR with its OSD.
If you use a hardware decoder for picture output you should switch on the connected TV now. If you use software output the client for this must be started after VDR.
First, you should learn your key definitions; that is, connecting keys on your remote control to VDR's internal commands.
Note: Just in case you need to edit the keyboard configuration, or (more likely) want to delete it to go back to learning the keys: VDR stores its key-definitions in /etc/vdr/remote.conf.
We begin with starting VDR:
Code Listing 7.1: Starting VDR
# /etc/init.d/vdr start* Preparing start of vdr:* config files ... [ ok ]* Waiting for prerequisites (devices nodes etc.) ... [ ok ]* Starting vdr ... [ ok ]* First start of vdr: No check for running vdr possible* until control device (remote/keyboard) keys are learnt!Note: Users of software decoders should now start the client program that opens the window to show the TV picture and the OSD.
Code Listing 7.2: Activating the software decoder for the client
(For users of vdr-softdevice)# ShmClient(For users of vdr-xineliboutput)# vdr-sxfe xvdr://hostnameThe most useful keys for VDR are:

• Cursor keys (Left/Right/Up/Down)
• Menu/Exit/Ok
• Colors (Red/Green/Yellow/Blue)
• Number keys (0-9)

Important: If you don't have many keys, make sure to assign these. (Some remotes have Play/Pause/etc. on the same keys as the colors, so use them for the colors).
Now that the basic installation is over, you need to configure VDR. Switch to your output screen and follow the on-screen instructions. VDR asks you to press various keys on your remote control to learn the correct key codes. If you don't own a remote control, you can use your keyboard.
Now you can add the VDR initscript to the default runlevel to get it started every time your computer boots up.
Code Listing 7.3: Adding vdr to the default runlevel
# rc-update add vdr default8. Troubleshooting
Note: If you need any help, you can always ask someone in #gentoo-vdr, or look around on our .... (forum adresini sildim...)
------------------------------------------------------



Updated January 2, 2007
Summary: This guide shows you how to prepare Gentoo Linux for DVB and VDR.

--------------------------------

NOT: Alıntıdır..........
aşşağıdaki adres....
kesin ayrıntılı bilgi orada....
************************************

http://www.gentoo.org/doc/en/vdr-guide.xml

************************************

bir de yardım için forum adresi vermişler...onu veremem...
forum kuralları gereği.... çünkü sanırım
üyelik istiyorlar....
***************************************
ayrıca almanca bilen arkadaşlar için....
vdr nin almanca sayfası.... ingilizcesi bile yapım aşamasında..... under constr....
http://vdr.repulse.de/

Türkçeyi sormayın.... arkadaşlar vakit bulunca bakacağım tercüme için... ya da vakti olan baksın...
zaten ingilizce metinde önemli yerleri şöyle bir işaretledim... "sanırım kod listelerini iyi bir linux kullanıcısının incelemesi gerek..."
....ve kullandığınız kernel (pardusta) kaynağa ve bu programa uyumlu mu ilk o kontrol ediliyor.... bölüm 2 ...kernel config inizi kontrol edin başlığı....
selamlar....

Konu: pardus ve skystar?

evet son not:

alıntıdır: ***********....
forum kuralları gereği linkini veremem...nette bulun...

selam
pardusta skystar 1 firmware lib/firmware klasörü içine kopyalanacak.

aşağıdaki satırlar /etc/modules.autoload.d/kernel-2.6 dosyasına eklenecek.
bilgisayar kapatılıp açılacak.

modprobe dvb-core
modprobe stv0299
modprobe saa7146
modprobe saa7146_vv
modprobe ttpci-eeprom

ayrıca vdr1.4.5 sorunsuz derlendi. buan ek olarak sc0.6.0 pluginide sorunsuz derlendi.

--------------------------------------------------------

arkadaşlar Pardus 2007 de vdr sadece skaystar1 de çalışıyor diğer kartlar da sadece kaffeine ve mythtv ile çalışıyor. bunun dışında çalıştırabilen var mı?


*****************************************


pardus 1.0 kurdum.şimdi güncellemeleri alıyorum kafein programında ss2 kartımı gördü ayarları çıktı lnb uydu seçimi felan ama antenim olmadığı için bakamıyorum

amd sempron 2500+
768 mb ram
256 mb nvidia geforce fx 5500
cd-rw
skystar 2
17" beko mon.
90 cm beko motorlu anten
DvbDrem
win XP SP2
********************************

evet işte böyle.... yeni kernel gerekli diyenler var.... yani ss1 o.k... ssk2 değil..
ancak mythtv plugine uyumlu mu daha bakmadım...
selamlar...

Konu: pardus ve skystar?

ayrıca .... bir not daha....
bunun linkleri bilgi amaçlı...




Technisat

From LinuxTVWiki


Jump to: navigation, search
A German Company that produces Digital-TV products based on US company's digital receiver chips FlexCopII, FlexCopIIb or FlexCopIII.
Device Description Skystar2/Sky2PC well-supported DVB-S PCI Card based on the B2C2 FlexCop2 or FlexCop2b with stv0299 or mt312 Airstar2/Air2PC DVB well-supported DVB-T PCI Card based on the B2C2 FlexCop2 or FlexCop2b with mt352 Airstar2/Air2PC ATSC well-supported ATSC PCI Card based on the B2C2 FlexCop2 or FlexCop2b with nxt2002 Cablestar2/Cable2PC soon-supported DVB-C PCI Card based on the B2C2 FlexCop2 or FlexCop2b with stv0297 Air2PC USB DVB supported DVB-T USB1.1 Device. Based on the FlexCopIII and mt352. Air2PC USB ATSC supported DVB-T USB1.1 Device. Based on the FlexCopIII and nxt2002. Sky2PC USB supported DVB-S USB1.1 Device. Based on the FlexCopIII and stv0299. Cable2PC USB soon-supported DVB-C USB1.1 Device. Based on the FlexCopIII and stv0297.

Konu: pardus ve skystar?

artık ipuçlarının yeterince tamam olduğunu düşünüyorum...

selamlar....

Konu: pardus ve skystar?

süpersiniz ya vallaha bukadar kısa zamanda bukadar çok şeyi çözmüşsünüz kendimden utandım vallaha hepinizin eline sağlık arkadaşlar saygılar...

Konu: pardus ve skystar?

dostum sen asıl buraya bak.... : ) : ) : )
selamlar....